DN50-DN3000 GRP Pipe for Seawater Desalination

• Customization: Available
• Surface Treatment: Gel Coat
• Color: Green
• Model NO.: DN5-DN3000mm
• Thickness: 5-40mm
• Usage: Environmental Protection, Industral, Water Supply & Drainage
• Product Categories: FRP Pipe
• Molding Method: Filament Winding
• Material: Fiberglass
• Fiber Type: GFRP
• Type: Polyester FRP
• Pressure Class: Pn16
• Stiffness: Sn5000
• Stanadard: Awwa C950
• Application: Seawater
• Purpose: Drinking Water
• Transport Package: Seaworthy
• Specification: DN50-DN3000
• Trademark: GJ
• Origin: China
• HS Code: 3917290000
• Production Capacity: 100000m

Product Description

Product Description

FRP pipe is consist of inner layer, Structural layer and outer layer. Its characteristics are:

1. Lightweight, high strength and high stiffness, its density is 1.5-1.9, equals one fifth of steel pipe, one fourth of cast steel pipe and three fourth of pretensioned concrete pipe(PCP).
2. Corrosion-resistant property. The Corrosion-resistant property of FRP pipe is mainly relied on the inner resin, and it can be selected based on the condition of the media.
3. Good hydraulic property. The inner surface of the FRP pipe is very smooth, its friction coefficient (f) is 0.000915 after performed the relative testing, the water conservancy factor (c) can be kept within 145 and 150 during a long period.
4. health property. For the pipe which be used for transporting the potable water, the food grade resin will be used. It has been approved by the relative national sanitary authority.
5. Shock resistance. It doesn't occur delamination and cracking under the condition of deformation of 25%.
6. Abrasive resistance. The inner surface is made of one kind of resin with good abrasive resistance, so it can improve the abrasive resistant property of the FRP pipe.
7. Low temperature resistant property. There will not be cracking under the condition of -40ºC and the strength doesn't decline.
8. It can be used for different kind of environment, such as beach, benthal, river, mountain area, marshland, desert and plain etc.

Detailed Photos

Product Parameters

Diameter (mm)	DN50, DN80, DN100, DN150, DN200, DN250, DN300, DN350, DN400, DN450, DN500, DN600, DN700, DN800, DN900, DN1000, DN1100, DN1200, DN1300, DN1400, DN1500, DN1600, DN1800, DN2000, DN2400, DN2500, DN2600, DN2800, DN3000, DN3200, DN3400, DN3500, DN3600, DN3800, DN4000
Pressure (MPa)	gravity, PN0.25, PN0.6, PN1.0, PN1.2, PN1.6, PN2.0, PN2.5, PN3.2
Stiffness (N/m2)	SN2500, SN5000, SN7500, SN10000, SN15000, SN20000, SN30000, SN50000

Packaging & Shipping

seaworthy packaging & shipping, telescope packaging

Installation Instructions

6.1 The section of the ditch
6.1.1 The surface of the ditch should be connected smoothly, and the wall of the ditch should be vertical.
6.1.2 The width of the ditch above the pipe only needs enough space to ram the backfill of the two sides of the pipe. If it is necessary can dig a hole in the coupling position, it means the width of the ditch need enlarge 2 meters, the length need enlarge 2 meters, the bottom of the ditch need decrease 1.5 meters, this hole should be filled up and rammed after backfill.
6.1.3 The depth of the ditch can be defined according to the following factors, such as the pre-designed device in pipeline, property, dimension of the pipe, the property of the soil, the static load and the dynamic load.

6.2 Steady ditch condition (see Fig. 5)

Fig.5
A---The backfill on site
B--- The backfill in the pipe area   the minimum height is 70 percent of the diameter
C---Base bed   minimum 15cm
D---Steady support
6.3 Unsteady ditch condition
These two ways of installation can be adopted if the unsteady ditch wall and the unsteady ditch bottom appear (see Fig.6 and Fig. 7).

Fig. 6
A---The support can be drawn out or not according to the site condition
B ---The backfill on site
C---The backfill in the pipe area   the minimum height is 70 percent of the diameter
D--- Base bed   minimum 15cm
E--- Base       minimum 15cm
F---Enough supports
G---The backfill
H---Steady support

Fig.7
A---The backfill on site
B---The backfill
C---Steady support
D---3 times of the diameter
E---The backfill in the pipe area   the minimum height is 70 percent of the diameter
F---Base bed   minimum15cm
G---Base      minimum 15cm

Our Advantages

our company established by several-manufacturers jointly, firstly product quality is ensured, secondly is delivery time is guranranteed.

After Sales Service

We will provide the complete service for the bidding goods prior to sale and post-sale, such as fabrication, transportation, spare parts and accessories. The technical staffs will install and debug at jobsite, make the equipment reach the requirements of the property and settle any problems arisen from design or fabrication during the installation freely.